A water heater, mainly an electric model, is a typical appliance. From one side of the tank, normal water enters.
A few electrical resistance elements treat the water from one side of the tank to the center of the water. Furthermore, when we turn on the tap, the water comes from another tank side.
It’s easy to install an electric water heater, even if you’re not an expert. A little basic electrical and plumbing work before technical installation will help. You can take the help of the water heater installation services if you are not satisfied with DIY. By calling them, you can save your money as well as yourself.
Let’s plunge into the blog and get complete information on installing the electric water heater.
Disconnect the power supply and water tube
From the circuit breaker board, turn off the electricity. Make sure you check that the power is off from the circuit breaker before working on it.
Detach cold and hot water supply lines. If you want to install copper pipes, you may need to cut them. However, it will help if you cut the tube according to the need. If you are unsure, then contact water heater installation experts, and they will do your job in the nick of time.
Drain the new water heater tank
Open a tap of hot water to run from it until it becomes cold. As a result, you’ll be able to drain your tank without getting burned. Use the controls on top of the water heater, then turn off the cold supply.
Drain the water heater by attaching the hose to the valve. Once the valve is open, you should drain the tank outside. You can take the help of water heater installation services if you are not sure what to do as they are experts in electric water heater services.
Remove electrical wires
Be sure to disconnect the electrical wires on top of the water heater. But before that, you should turn off the circuit breaker from the breaker box. However, before starting, you should check all the wires with the help of the voltage tester.
Please mark and cap the wires if you install the new water heater to avoid future confusion.
Before disconnecting the old heater, drain it.
You will need to drain your water heater if it is currently installed in your house. Furthermore, you will need a bucket and a pipe for this project.
To remove the old wiring and mounting brackets, you must unscrew them. If you are going to replace any existing wiring or pipes, take care not to damage them. Having to replace everything will increase the project’s cost and time.
Take off the front cover
It is necessary to withdraw the cover from the link box to access the wiring. Connect the green ground screw with the earth wire. Join the remaining wires by winding them with wire connectors. Hereafter replace the junction box cover.
Heater Mounting
The unit must then be mounted on the wall. A chaotic or messy area of your home is not the best place to put your water heater. The unit should be readily available in case of an emergency. Several screws and the mount provided in the package are all you need to mount the water heater. If your unit comes with instructions, follow them.
Easily connect any pipe
To distribute hot water throughout your home, you’ll need to connect the pipes after you have mounted the device. They will connect to and from your water heater, and it is best to find them at the bottom of the unit.
Refer to your installation diagram for instructions on where to connect your unit. Don’t hesitate to call a water heater installation service if you’re unsure.
Electric water heaters should use stainless steel pipe material. However, high temperatures will not affect the system’s flexibility or accessibility. If stainless-steel pipes are not available, copper or PVC lines are acceptable. It helps to quickly detach strong connections on flexible stainless-steel pipes if you plan to clean them frequently.
Set up flow and pressure valves
Flow and pressure valves are easy to install because they follow the connection of the lines. When a heater needs repair, you can turn the water supply off to the heater instead of turning off your entire house’s water supply.
Local plumbing authorities would require pressure valve installations. Electric water heaters should have a pressure release valve located on their side marked “hot water.”
Adding a second one to the heater would ensure maximum safety.
Switch on the circuit breaker
It is safe to switch on the circuit breaker since there is no need to work on the heater itself.
Test outlets & temperature
It is important to configure the water heater’s temperature settings once the unit is turned on. In order to avoid potential burns, you should not use these units in the highest settings. It is essential to check the temperature and immediate warming of hot water outlets throughout your home at this point, including faucets, showers, dishwashers, and clothes washers. Changing the temperature settings may be necessary if the water is too hot.
Advantages of an electric water heater
An easy-to-use water heater
It requires very little maintenance and installation and requires no ventilation.
An affordable option
The cost of an electric water heater is usually lower than the cost of other types of water heaters, and electric water heaters do not require fuel to run.
Efficient use of energy
Energy efficiency is one of the best features of electric water heaters.
Water availability
Hot water is always available through electric water heaters due to their ability to maintain their temperature. There is no doubt that the heater’s insulation directly affects its internal temperature.
The bottom line:
The above blog describes the procedure followed for electric water heater installation. You can prefer installing it yourself, but it is not recommended. An experienced water heater installation professional can help you install a new water heater.
Author Bio:- Josephine Floyd
Josephine Floyd is a marketing head at L&S Turnkey. He is an experienced marketing leader with over 12 years of experience in the plumbing industry. With extensive knowledge of severe water damage, mold damage, and fire damage, as well as general plumbing services, he writes articles about water and flood damage repair and restoration along with heating installation, maintenance, and repair to make readers aware of the potential risk and quick actions they can take to reduce damage. Keep reading his latest articles to have an understanding of whether your plumbing system is intact or not; if not, what you should do to fix it.
Apart from that if you want to know about 5 Actions to Take When a Water Pipe Bursts Indoors then please visit our World page